Upper and Lower Plates with bushings installed are pre-fit, ready to drop in with no machining required.

if you chose to purchase the bushing without the plate they will need to be sized after being pressed into the plate, this will require access to a lathe or reamer

New, Never Used Center Chunk: $1350.00

Reman Center Chunk, all bearings and gears inspected for wear with new seals, all bearings set to factory preload and all gear backlash set to factory specifications: $799.99

Used/Clean with New Pinion Seals installed, Crown and Pinion backlash checked, gasket surfaces cleaned and ready for install, bearings not inspected and factory preload not checked. Slight wear and surface rust is normal: $549.99

Used/Greasy, factory pull out, no bearings, seals or gears checked, in usable condition, but sold as is: $349.99

2.5 Ton Front Axle Drive Flange, Stock 16 coarse Spline

Price is for 1 drive flange in good used condition 

Flanges can be machined to allow "unlocked" application

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

1410 Or 1480 Driveshaft Adapters

2.5 Ton Used Driveshaft, 
1410 U-Joints

these come as used surplus drive shafts, all Spicer genuine parts including greasable U-joints, and both 4 bolt flanges that will bolt up to your 2.5 ton axles, 29" long collapsed, 32.25" long extended, 3" diameter tube 

1480 Driveshafts- 30" long, used take off drive shafts, complete with 4 bolt Rockwell adapters 

1550 - 51" long, used take off drive shafts, complete with 4 bolt Rockwell adapters 

Contact for other alternatives, we also sell drive shaft tube if you need to extend them 

Price is for 1 fill plug in good used condition, 1/2" drive with copper gasket 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

Kit includes:

• 24x Anti Vibration Washers
• 24x 3/8" x 1" Grade 8 Bolts

When flipping the hubs on a steer 2.5 Ton Axle to run a narrow track width, you will need to remove the factory Spindle Studs, then replace them with this kit that allows the backside of the Wheel Studs to clear the Spindle bolt heads. Keep in mind some grinding on the backside of the Wheel Studs will be required. This kit will make sure the amount of material needed to be removed will be an absolute minimum.

2.5 Ton Hub (Wheel) Socket, undo and tighten spindle nuts.

2.5 Ton Stock Hub Replacement, New

2.5 Ton Re-man hub, good used condition, cleaned up and inspected 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

2.5 Ton King Pin Shim these fit on the upper king pin and take up any slack in the knuckle 

Price per shim

King Pin Shim Kit can be used to adjust stock shims, and includes one shim each in the following thicknesses:

• 0.001"
• 0.0015"
• 0.002"
• 0.003"
• 0.004"
• 0.005"
• 0.006"
• 0.007"
• 0.008"
• 0.010"
• 0.012"
• 0.015"
• 0.020"
• 0.025"
• 0.031"
  
• 0.047"
• 0.062"
• 0.093"
• 0.125"
  

Works with the following Axles:

• 2.5 Ton
• 5 Ton
• Meritor
• F106 

Maintenance Manuals for all our Axles and T-600 Transfer Case

Pinion crown nut for the 2.5 ton axle, 

Price is for 1 good used nut 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

4 bolt pinion flange for the 2.5 ton axle

price is for 1 yoke in good used condition 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

2.5 Ton Pinion Yoke Washer, this is a hardened washer that sits behind the crown nut holding on the pinion yoke 

price is for 1 good used washer 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

Overall Length from under the head of the bolt: 2.8435"

Will work for both 2.5 Ton Axles and 5 Ton Axles that are not using the factory drum brakes

Overall Length from under the head of the bolt: 2.5715"

2.5 Ton front spindle stock

price is for 1 good used spindle

we can drill out the mounting holes to 7/16 for an additional $25 before shipping if you are running upgraded knuckles, please contact us before ordering if you requite this service 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

7/16" Grade 8 Bolt Kit for the Upgraded Plate Steel Knuckles

Includes:

• 24 7/16" NF Grade 8 Bolts
• 24 Two Piece Nordlock Washers

This lock tab fits between the 2 nuts that hold your hub bearings on, these should be replaced every time the spindle nuts are removed as they can become damaged  allowing your spindle nuts to become loose and the hub falling off the vehicle

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **

2.5 Ton Spindle Nut

2 Used per Hub

Price is for 1 nut 

** Parts are refurbished, meaning they may show slight signs of wear, but will work exactly as intended, if you prefer brand new please contact us for options **