PN: MR 5012 A

These are a plate steel upgraded knuckle  for the Meritor RF611 axle, made from a high grade T1 steel they are extremely strong and will not fatigue and crack like factory knuckles, they are also 15lb lighter than stock saving you 30Lb per axle

These are jigged and hand welded for superior craftsmanship and a perfect fit 

They include 1/2" steer lugs that tie into the spindle plate also increasing strength

Additional arms are available if you would like to do a triple shear setup with a tire rod and steer ram

Includes:

• 2 Fully Welded Knuckles 
• 4 Steer Lugs, shipped loose 
• 4 Gussets for Steer Lugs, shipped loose 
• 20 Grade 8 Spindle Bolts 
• 20 Nordlock Spindle Lock Washers 

PN: MR 2201

WCR's Meritor 611 Pinion Brake Kit contains everything you need to set up your Meritor Pinion Braking System.

• 12" WCR Non-Vented Rotor
• Pinion Mounted Flange
• Wilwood Caliper
• Wilwood Brake Pads
• Pinion Mounting Bracket and Grade 8 Hardware. with the ability to choose what side to run it on, there are two different Mount Brackets and Bolt Kits available

12" diameter made from solid billet steel will not warp like plasma cut rotors, or heat check and fail like cast rotors. No vent holes prevent mud and sand from building up between the pad and rotor causing premature wear, the thick steel rotor is very resilient to damage if it comes in contact with an obstacle. Also because they are 3/4” thick solid steel, this means it is possible to machine them multiple times and bring them right back to new!

These are premium brake kits with top of the line parts, designed specifically for those who desire the best and safest brake Kit on the market!

**Please note circled areas pictured, may need to be clearanced for proper fitment on back of Driveshaft Adapter 4 Bolt Flange. 

• 1x LH Arm
• 1x RH Arm
• 2x 1" Taper Elimination Cones for the stock tie rod hole

• 8x 7/8"x3" NC bolts 
• 2x 1" bolts 
• 14" long if heim is run above the arm
• 12" if heim is run below the arm 

If you would like to purchase King Pin caps with your High Steeer Arms, you can find them here --> https://westerncanadianrockwell.ca/products/king-pin-cap-meritor-machined?_pos=3&_sid=dddd7cd7f&_ss=r

*PLEASE NOTE* Core charge to return caps is $120 CAD.

Upper king pin cap, machined off for a nice flat surface, perfect to add high steer arms or shock mounts

Available in Welded and Non-Welded DIY configuration

Welded Sockets are laser cut end caps, welded to a piece of pipe, socket drive is 1/2"

DIY Kits Include: PN: MR 7206 A

• End Cap with 1/2" Drive 
• Socket Cut out

DIY Kit requires 5.5" of 4.5" OD Tube

Welded Kit Includes: PN: MR 7207 A

• Fully Welded Socket with End camp and Socket cut out

The Tierod Taper Kit allows you to remove the factory taper from the steer arm of the Knuckle allowing you to run a bolt and Heim Joint setup

Sold in Pairs

Breathing line kit for your Rockwell Axles, will fit most Axles.

Kit includes enough line and fittings for one Axle: 

• 25 feet of 1/4" Air Line
• 1/8" NPT Compression Fitting
• Nylon tubing is flexible and durable but will not collapse like rubber hose

Thrust Washer, for the Meritor Front Axle Shaft. This is the same washer that is found in the spindle and the axle tube.

Item #41 on parts breakdown