Breathing line kit for your Rockwell Axles, will fit most Axles.

Kit includes enough line and fittings for one Axle: 

• 25 feet of 1/4" Air Line
• 1/8" NPT Compression Fitting
• Nylon tubing is flexible and durable but will not collapse like rubber hose

The Tierod Taper Kit allows you to remove the factory taper from the steer arm of the Knuckle allowing you to run a bolt and Heim Joint setup

Availablie is 1" or 3/4"

Sold in Pairs

Eliminate factory Cone Washers when using full Hydraulic Steering

Made from High Strength Laser Cut T1 Steel. Will not flex or bend like normal mild steel, weld washers are not required, these are built from the highest grade steel on the market.Width can be adjusted for different Heims. Contact for Custom Size Bolt Holes

This is for one Axle, comes with:

• Top Plate (Front, Front Flipped, Or Rear)
• Side Plates And Spacer Plate
• 2 Short Lower Link Mounts
• 2 Long Lower Link Mounts
• 4 Flat Mount Link Tabs

Bolts Required (Option to purchase bolt kit):

• (4x) 1/2"x2-1/2" NC Gr 8 Bolt
• (10x) 3/8"x1-3/4" NC Bolt Gr 8
• (8x) 3/8"x1-1/4" NC Bolt Gr 8 

When installing the 5 Ton Top Hat, leave the diamond shaped side plate and rectangle top in place. Due to difference in manufacturing, the top may have to ground down a bit slightly in the area shown, in the spacer plate image.

PN: 5T 2201

EMF's Rockwell 5 Ton Pinion Brake Kit contains everything you need to set up your Rockwell Pinion Braking System.

• Wcr Non-Vented Rotor
• Wilwood Caliper
• Wilwood Brake Pads
• Pinion Mounting Bracket and Grade 8 Hardware. with the ability to choose what side to run it on, there are two different Mount Brackets and Bolt Kits available

12" diameter made from solid billet steel will not warp like plasma cut rotors, or heat check and fail like cast rotors. No vent holes prevent mud and sand from building up between the pad and rotor causing premature wear, the thick steel rotor is very resilient to damage if it comes in contact with an obstacle. Also because they are 3/4” thick solid steel, this means it is possible to machine them multiple times and bring them right back to new!

These are premium brake kits with top of the line parts, designed specifically for those who desire the best and safest brake Kit on the market!

5 Ton Take Out Detroit Locker

5 Ton High Steer Arms, made from T1 steel, with a built in double shear tube to help tie into the stock steer arm, sharing the load of the Steering Ram. Heim Joints can be run above or below the arm by shortening the tube.

High Steer arms are sold with the intention to run the Heim Joint above the Steer Arm, if you wish to run the Heim below the Steering Arm, the tube will need to be modified once received or we can modify for you, if Heim Joint width is specified before ordering.

  Kit Includes:

• 1x LH Arm
• 1x RH Arm
• 2 Taper Elimination Cones for the stock tie rod hole

Optional Items Include: 

• 8x 5/8NC bolts 
• 2x 1" bolts with lock nuts 
• 10.5" long if heim is run above the arm
• 9.5 if heim is run below the arm 

Our version of the 5 Ton high clearance Diff Pan, of course it's made from the same high strength T-1 steel we build everything from.

Each pan is fully welded on both sides, meaning it will be the strongest part of your Rockwell housing! The added clearance will help keep you from dragging your diff pan on obstacles. We've also designed the pans to have the least amount of flat edges that way they're a lot less for you axle to get hung up on!

High steer ram mount for 5 ton axles, this allows you to mount a double ended ram on the chunk, keeping it up out of the way of rocks, mud and logs, this kit bolts on so welding and fabrication is not required, made from 3/8 T1 steel it is jigged and fully welded 

High steer arms are sold separately and will be required 

This kit only works on the 5 Ton Small Pinion Bearing side, this ram mount kit will only really work on the back side of a rear steering axle. The correct configuration for a front axle, is with the big pinion bearing facing forward. This allows the crown and pinion in the differential to mesh on the drive side of the ring gear. Please contact us if you have any questions or you would like further details

Includes:

• (1x) Power Steering Pump for Full Hydraulic Installations with Rockwell Axle
• (1x) Remote Reservoir with Hose Kit
• (1x) Orbital Valve 200cc
• (1x) Orbital Valve Mount

Kit Includes:

• High Steer Ram Mount Front
• High Steer Arms
• 3x11 Steering Ram including;
• Ram
• (4x) Clamps
• Monster Clevis Kit
• Tie Rods with 1.25" Rod Ends

Turns Lock to Lock 3x11 with the following Orbitals:

• 200cc 4.8 Turns
• 250cc 3.8 Turns

This kit only works on the 5 Ton Small Pinion Bearing side, this ram mount kit will only really work on the back side of a rear steering axle. The correct configuration for a front axle, is with the big pinion bearing facing forward. This allows the crown and pinion in the differential to mesh on the drive side of the ring gear. Please contact us if you have any questions or you would like further details

3.0" Bore X 11" Stroke X 1.5" Rod

Features Grooved Non-Slip Casting and machined clamps.

Linkage kits are designed to work with 5 Ton Rockwell Axles, the ram will work with Meritor 611 and Axletech 4000 as well. Please contact us for Linkage Kits for the Meritor 611 and Axletech 4000 axles.

Includes:

• (1x) SC2228 - Single Ended Assist Cylinder 3.0 Inch Bore X 11.0 Inch Stroke X 1.50 Inch Rod

Optional Kit:

Includes:

• (1x) SC2228 - Single Ended Assist Cylinder 3.0 Inch Bore X 11.0 Inch Stroke X 1.50 Inch Rod
• (4x) SCCL05KF - Cylinder Mounting Clamps
• (1x) RED-SC500 Monster Clevis Joint Kit 
• (1x) RED-TR500 Tie Rods with 1.25" Rod Ends

Turns Lock to Lock 3x11 with the following Orbitals:

• 200cc 4.8 Turns
• 250cc 3.8 Turns

PN: 5T 5012 A

5 Ton upgraded HD plate steel knuckles, constructed from high strength T1 Steel. These knuckles will not fatigue or crack like the factory cast knuckles, they will not stretch or deform like knuckles made from mild steel.

Jigged and hand welded for a perfect fit, available with double or triple steering lugs

3 Week delivery time, now accepting Pre-Orders

Leaf Spring Mounting Kit, comes with 2 Lower Spring Perches, and 2 Upper Plates, additional Shock Mounting Brackets are available, U-Bolts are not included