Fits the Following Vehicles:

Front Wheel SEAL

• 1980 to 1998 FORD F250, F-350 with Dana 50 IFS front 
  
• 1978 to 1987 CHEVY/GMC K30, K 35 with Dana 60 Front Axle
• 1978 to 1998 FORD F-250 with Dana 60 Front Axle
• 1980 to 1998 FORD F-350 with Dana 60 Front Axle

This is the lower King Pin Seal used on front Dana 60 King Pin Axles.

Will work with Dodge, GM and Ford. 

These are a genuine replacement seal for the output yokes on all NP205.

Make sure to measure the diametere of the seal surface on your yoke before ordering. 

• DANA 60 Front or Rear end Pinion Seal
• Fits DANA 60 Car Rear Ends
• Fits DANA 60 Truck Rear Ends
• Fits DANA 60 4x4 Truck Front Ends
• Fits Dodge with DANA 60 front or rear diff
  • 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982,1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999
• Fits 1978 to 1998 Dana 60 FRONT in FORD F-250 and F-350 4x4 trucks
• Fits 1978 to 1998 Dana 60 REAR in FORD E-250, E-350, and F-250 and F-350 4x4 trucks
• DODGE W200, W250, W300, W350, D600, D700
  • 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993
• Fits 1974 to 1988 Jeep J20 J30 with Dana 60 Rear end

• Fits Chevy, GMC, Ford, Dodge with DANA 60 front or rear diff

• Fits 1978 to 1998 Dana 60 FRONT in FORD F-250 and F-350 4x4 trucks
• Fits 1978 to early 2000 Dana 60 REAR in FORD E-250, E-350, and F-250 and F-350 4x4 trucks
• Check Bill Of Materials numbers for 1999 and 2000 vehicles

• DANA 61
• DANA 70
• CORVETTE DANA 44 Rear end Pinion Seal
• Fits 1984 TO 1996 CORVETTE DANA 44 Rear end with 29 spline pinion

This is a factory replacement Bearing and Seal Kit for the Dana 60 Spindle. 

Will work with Dodge, GM and Ford King Pin Axle spindles.

These are Heavy-Duty Bronze Upper Kingpin Bushings for Steering Knuckles on a Dana 60. 

These are designed to replace the stock nylon cone bushings, which are prone to premature wear when used off-road with large heavy tires. 

Fits all Open Knuckle King Pin Dana 60's Found in Chevy, Dodge & Ford.

• Designed to be used with Aftermarket adjustable-preload high-steer arms
• Included roll pin prevents rotation of the bushing within the knuckle
• Improved grease passage allows for proper pressure greasing and easier servicing
• Eliminates steering shimy common to kingpin knuckles
• Threaded extraction holes simplify removal

Designed to replace the wear items in the lower king pin on a Dana 60.

Will work for Dodge, GM and Ford. 

Yukon King Pin Rebuild Kits and components provide strength and reliability for street and off-road applications. This is a complete King Pin Rebuild Kit.

Kit fits Dana Spicer 60 and rebuilds one side. 

Kit Includes:

• King pin, bushing, seals, bearings, cap, gasket and hardware.
  
  

The kit will fit all dana 60 king pin axles found in:

• Chevrolet K30 (1977-1986)
• Chevrolet V30 (1987-1988)
• Dodge W250 (1981-1993)
• Dodge W300 (1975-1980)
• Dodge W350 (1981-1993)
• Dodge W200 (1975-1980)
• Ford F-350 (1979-1991)
• Ford F250 (1978-1979)
• GMC K3500 (1979-1986)
• GMC K35 (1977-1978)
• GMC V3500 (1987-1987)

Compatible Differentials

• Dana 60 Front
• Reverse Rotation 

WCRs truss kit for dana 60, dana 70 and 14 bolt rear axles.

• Easy install and setup.
• Built from high strength 1/2" thick steel.
• Very versatile can be mounted with the axle clocked in almost any direction.
• Gussets can be trimmed to fit your application.

This is a factory replacement flange head style bolt for Dana Axle Differential Covers. 
3/8 threads.

Factory Length, will not work with thicker aftermarket covers.

Precision Gear GM14/MSPL 10.5" 14 Bolt Mini Spool General Motor

Lead time 1-2 Weeks

Pinion Flange to adapt a Dana 60/70/80 axle to a 1410/1480 Driveshaft

Dana 60